Textile Gate | Textile Gate Syllabus
TEXTILE ENGINEERING AND FIBRE SCIENCE Section 1: Textile Fibers Classification of textile fibers; Essential requirements of fiber forming...
top of page
Search
textilecoach
Feb 16, 20211 min read
Picking | Objectives of Picking | Types of Picking | Classification of Picking
Pick: Pick is a single weft yarn in woven fabric. Picking: It is the process of weft yarn insertion in the warp shed. Picking is the...
textilecoach
Feb 15, 20211 min read
Timing of Shedding | Early Shedding | Late Shedding | Normal Shedding
Shedding mechanism is set according to the picking and Beat-up motions. Timing of shedding is set with respect to crank shaft position....
textilecoach
Feb 13, 20212 min read
Mixing and blending
Mixing: It is a process in which 2 to 3 varieties of cotton are mixed in specific proportion to get the optimum mix which produce quality...
textilecoach
Feb 10, 20212 min read
Side Weft Fork Mechanism
Side weft fork mechanism comes under the weft stop motion. It works on alternative picks. Following are parts of side weft fork...
textilecoach
Feb 8, 20210 min read
textilecoach
Feb 8, 20211 min read
Dobby pegging and lagging
Dobby pegging and lagging This is a process by which the lags are connected to each other and pegs are fixed to the lags. The pegs are...
textilecoach
Feb 8, 20213 min read
Classification of Warping Machines
Warping: it is defined as a process of combining of ends from cone or cheese or spool or double flanged bobbin on to warper beam. Every...
textilecoach
Feb 3, 20211 min read
Comparison between Beam and Sectional warping | Defects in Beam warping
Comparison between Beam and Sectional Warping: Defects in Beam Warping:
textilecoach
Feb 3, 20211 min read
Keighley Dobby
The negative dobby with single jack is known as Keighley dobby. The negative dobby with double jacks is known as climax Dobby. It...
textilecoach
Feb 1, 20212 min read
Classification of Dobby
It is a shedding device placed on top of the loom. It provides figuring effects and produces smaller motives. It is normally built to...
textilecoach
Feb 1, 20211 min read
Common elements of Dobby and their function
Faults in dobby weaving: Peg falling: This is due to continuous use of old lattices for long time where in the used peg may get worn out...
textilecoach
Feb 1, 20213 min read
Types of Shed
Shed: Shed is the temporary separation between upper and lower warp yarns to facilitate the weft insertion. Types of Shed: Sheds are...
textilecoach
Jan 29, 20211 min read
Loom temples
Normally warp sheet contracts from 2 to 15% in width from reed to the cloth due to interlacement of warp and weft. This can be prevented...
textilecoach
Jan 28, 20211 min read
Tertiary/Auxiliary motions of loom
Weft stop motion: These motions stop the loom immediately in the event of weft breakage or weft running out. There are 2 types of weft...
textilecoach
Jan 27, 20213 min read
Shedding | Tappet Shedding | Positive Tappet Shedding | Negative Tappet Shedding
Shedding is a process by which warp sheet is divided into two which will facilitate the passage of weft yarn from one end to another end...
textilecoach
Jan 24, 20212 min read
Elements of beam warping
Creels Warp stop motion. Fan Powerful clutch and brake Measuring motions Antibound let off motion. Foot pedal Beam bracket Beam doff and...
textilecoach
Jan 21, 20213 min read
Creels in Sizing
Creel is a platform for placing warpers beam. The function of the creel to allow steady and smooth unwinding of warp yarn from the...
textilecoach
Jan 20, 20214 min read
Types of Creels | Creels in Warping
Creels in Warping Creel: Creel is a platform which holds the supply packages like cone, cheese or spool in warping process. Warping...
textilecoach
Jan 19, 20212 min read
Loom Motions
Loom motions are classified into three types Primary Motions Secondary Motions. Tertiary Motions / Auxiliary Motions. Primary Motions of...
bottom of page